fathers day shirts. Sure, you may move the Hallmark course this Father’s Day, but Cool and creative Fathers day shirts cards are just so plenty better — specifically while they’re shaped appreciated little mini get dressed shirts and are so stinkin’ adorable you can’t even stand it. If the dad on your life fits up for work each day, you virtually can’t cross incorrectly with this clean Father’s Day card DIY.
fathers day shirts, You can make your personal quirky Father’s Day blouse card — using any paper sample to match Dad’s favored blouse — in only some easy steps:
- Decorative paper for a shirt (8-1/2 x 11-inch cardstock was used here)
- Decorative paper for accessories
- Glue or double-sided craft tape
- Bone folder
- Hole punch
- Decorative wrapping paper
- Instructions for DIY Father’s Day shirt card
Throughout the craft, it’s important to create crisp folds. A bone folder can help make this easier.
Step 1: Create vertical folds
If using decorative paper, turn the paper over so the right side is facing down. Fold the paper in half.
Lay the paper flat and fold each side up into the centerfold. Open up a paper and lay it flat.
Step 2: Fold bottom corners
Take the bottom left-hand corner and fold it into the first fold line. Repeat on the other side.
Close the folds back up to the outside sides align with the centerfold.
Step 3: Create sleeves
Take the bottom side of the paper and fold it up just beyond the upside-down V. Make a nice, crisp fold.
Open bottom folds out again.
Where the paper joins in the middle of the center V, take the inside point and fold it out to the left side edge of the paper.
Repeat on the other side. Note: the paper will come up slightly on the bottom.
Take the bottom of the paper and fold it up to just beyond the upside down V. Crease it nice and sharp.
Step 4: Create the collar
Flip the paper over and go to the top. Fold the top portion over about 1/2-inch (approximating the measurement is fine) so there is a crease at the top.
Flip the paper over so the top crease is to the back. Bring the top left corner to the centerfold so that it creates a triangle shape.
Repeat on the right side. Make sure folds are sharp.
Step 5: Complete the shirt
Bring the bottom end up and tuck it underneath the top flaps (the shirt collar). Now you have your basic shirt shape!
Step 6: Add a personal message
To add a personal message inside the card, cut out a piece of cardstock that can fit inside the card. The one used here is approximately 3-1/2 inches by 5-1/2 inches. Secure it to shirt with glue or double-sided tape. Write dad a note.
Step 7: Accessorize the shirt
Add embellishments to the outside of the shirt to give it some of dad’s style. Ideas to consider include a tie, pocket, bowtie, or buttons.
To make a tie: cut a 1/2-inch strip of decorative paper. If you know how to knot a tie, now’s the time to show your skills. If not, fake it by looping strip around the top until a faux knot is created.
Snip the bottom corners of the paper to create a pointed end. Secure to shirt with a dab of glue or double-sided tape.
Father’s Day shirt card: Tie and hanky
To add a pocket, cut a small square of decorative paper and round-out the bottom edges (tip: use a circle template to get around the bottom). Using the same paper as the personalized message, free-hand cut a small shape to serve as the hanky. Secure it to the shirt with glue or sticky tape.
Father’s Day shirt card: Bowtie and buttons
To add a bowtie, cut a small rectangle and slightly snip the corners on a diagonal. Add buttons by using a hole punch. Secure it to the shirt with a dab of glue or sticky tape.
Wrapping paper also works as a substitute for cardstock or decorative scrapbooking paper. This one was made from leftover Christmas wrapping paper. Wrapping paper wrinkles a little easier, though, so if you’re using it, plan to make one as a mockup or be very precise when making the first folds. fathers day shirts